Page D3.2 . 22 October 2008                     
ArchitectureWeek - Design Department
NEWS   |   DESIGN   |   BUILDING   |   DESIGN TOOLS   |   ENVIRONMENT   |   CULTURE
< Prev Page Next Page >
 
DESIGN
 
  •  
  • Small Packages
     
  •  
  • Oslo Opera
     
  •  
  • Designing Fabric Structures
     
  •  
  • Newseum by Polshek

    [an error occurred while processing this directive]
    AND MORE
      Current Contents
      Blog Center
      Download Center
      New Products
      Products Guide
      Classic Home
      Architecture Forum
      Architects Directory
      Topics Library
      Complete Archive
      Web Directory
      About ArchWeek
      Search
      Subscribe & Contribute
      Free Newsletters
       

     
    QUIZ

    [an error occurred while processing this directive]

    Designing Fabric Structures

    continued

    Membrane plates are custom-designed plates used to link the membrane and edge cables to the structural supports. In most cases the fabric forms a curved edge, or catenary, between connection points, requiring a cable, webbing belt, or rope to carry loads to the major structural points.

    [an error occurred while processing this directive]

    Catenary describes the scalloped edge shape of the boundary of a uniformly stressed fabric structure attached only at specific end points or nodes. Catenaries are usually curved inward ten to 15 percent of the total length of the span.

    The cable, belt, or rope is usually inserted in a cable cuff, an edge treatment created either by folding the edge of the material over itself to form a pocket, or by attaching a ready-made pocket along the edge. The shallower the curve along the perimeter, the more tension there is in the cable and ultimately in the overall structure and foundation.

    Very high tension loads require a cable-strap treatment, which consists of a continuous clamping of the edge with a series of steel or aluminum straps spaced at specific intervals to support a cable that cannot be inserted in a cable cuff. Cable straps can increase the cost of a fabric structure substantially.

    Form-Finding

    Once the primary points have been determined, the next step is form-finding, or the art and engineering of ascertaining the most efficient structure that can be fabricated with as little waste as possible. In form-finding, it is just as important to design a structure that can be easily transported and installed.

    There are two methods of form-finding: physical modeling and computer-aided design. Fabric structures may be visualized with physical models or full-scale prototypes, depending on the complexity of the design. Models are created by stretching nylon stockings over wire frames. Working with physical models or prototypes enables the designer to view the structure from any angle.

    However, most fabric structures today are modeled with sophisticated computer software programs. These programs allow the designer to create a three-dimensional model that can be viewed at various angles; they also allow customization to provide information for facilitating fabrication and installation.

    The programs can calculate the amount of fabric required; the dimension of each fabric piece; the size and length of structural members; the size, length, and tension of cables; and the necessary hardware. With a software program, the designer can modify the shape more easily than with a physical model.

    Structural Analysis

    The last step in the design process is analysis of the structure's response to loads, including dead loads and live loads, such as snow, wind, people, and equipment. Structural analysis identifies areas of possible ponding (water collecting on a flat area) and shows where high stresses are located on the structure. The analysis enables the designer to determine reactions, size structural members and cables, determine the appropriate fabric, and create computer-generated cutting patterns.

    Computer patterning is the process of developing a two-dimensional representation of a three-dimensional membrane surface. Patterns are created after receiving results of a biaxial test of the specified materials done by the fabricator or provided by the manufacturer to determine the compensation factors required for the specific project. A biaxial test is the testing of a membrane in both the warp (threads running the length of the roll goods) and fill (threads running across the width) directions to calculate the expansion of the material under a given loading condition.

    Compensation factors are the reduction made to a cutting pattern to allow for the expansion of the membrane once in tension. In some cases, decompensation — addition made to the length of a piece of the membrane that was shortened by compensation — is required to meet certain geometric conditions, such as fixed points, where there is no access for tensioning. The panels are sized according to the width of the fabric being used.

    Materials

    Today's architectural fabrics are composites of woven substrate fiber protected by an applied coating or polymers of films and laminates. New fibers — primarily nylon, polyester, polyethylene, and fiberglass — have been developed to meet the need for materials with high strength, long life spans, and a high modulus of elasticity. The woven substrate provides the basic tensile strength of the material and its resistance to tearing. The finish coating applied to the substrate material seals the fabric against weather and dirt, provides resistance to UV light, serves as a medium for joining panels, and incorporates fire-resistant properties.

    The most important quality in choosing material for a fabric structure is its fire resistance. National Fire Protection Association (NFPA) 701 is the most common fire test for textiles and films. The American Society for Testing and Materials (ASTM) is another recognized standard for a wide range of materials, and ASTM E-84, 108, and 136 are common tests related to fabrics for membrane structures.

    The latest architectural fabrics used for a building envelope respond to heat and light much differently than previous generations of fabric did. They also offer features and benefits different than conventional construction materials.   >>>

    Discuss this article in the Architecture Forum...

     

    Continue...

    ArchWeek Image
    SUBSCRIPTION SAMPLE

    Vertical Teflon®-fabric fins on the Phoenix Central Library block direct sunlight and heat while still admitting some light.
    Photo: Courtesy W.W. Norton Extra Large Image

    ArchWeek Image

    A grill of horizontal fabric shades protects the heavily glazed facade of the Mesa Arts Center.
    Photo: Courtesy W.W. Norton Extra Large Image

    ArchWeek Image

    In the Zanzibar Tent, a tensile-fabric roof extends beyond the boundaries of the house, creating covered outdoor spaces.
    Photo: Nalzil

    ArchWeek Image

    The fabric roof of this bandshell in Charlotte, North Carolina, was designed and built in the 1960s.
    Photo: Samuel J. Armijos Extra Large Image

    ArchWeek Image

    The temporary Buckingham Palace Ticket Office in London was designed by Michael Hopkins Architects with Architen Landrell.
    Photo: Hopkins Architects/ Architen Landrell Extra Large Image

    ArchWeek Image

    Designed by Canotec, the canopy of the Founder's Center in Staubing, Germany, is a simply curved form.
    Photo: Canotec Extra Large Image

    ArchWeek Image

    Curving glue-laminated beams support the canopy at the Founder's Center.
    Photo: Canotec Extra Large Image

    ArchWeek Image

    Fabric Architecture by Samuel J. Armijos.
    Image: W.W. Norton Extra Large Image

     

    Click on thumbnail images
    to view full-size pictures.

     
    < Prev Page Next Page > Send this to a friend       Subscribe       Contribute       Media Kit       Privacy       Comments
    ARCHWEEK  |  GREAT BUILDINGS  |  ARCHIPLANET  |  DISCUSSION  |  BOOKS  |  FREE 3D  |  SEARCH
      ArchitectureWeek.com © 2008 Artifice, Inc. - All Rights Reserved