Page B1.2 . 24 April 2002                     
ArchitectureWeek - Building Department
< Prev Page Next Page >
  • Frame-and-Panel Cabinetry
  • ABCs of Videoconference Rooms

    [an error occurred while processing this directive]
      Current Contents
      Blog Center
      Download Center
      New Products
      Products Guide
      Classic Home
      Architecture Forum
      Architects Directory
      Topics Library
      Complete Archive
      Web Directory
      About ArchWeek
      Subscribe & Contribute
      Free Newsletters


    [an error occurred while processing this directive]

    Frame-and-Panel Cabinetry


    Visually speaking, rectangular panels are more attractive than square ones. For this reason, square openings are usually divided into two doors (or one door with two rectangular panels). Otherwise, I like using a numerical proportioning system for calculating door size.

    Once I've settled on the overall dimensions and proportions, I turn my attention to visual details. The most common panel edge is a flat bevel. But the edge can also be a curve, ogee, or a simple bevel. The panel shape can be square, arched, tombstone, or cathedral. Once completed, the overall effect of the design is strong, so I'm careful to chose details and proportions that complement rather than compete with the overall design of the piece on which the panel is to be used.

    Panel-Raising Jig for the Table Saw

    Panels can be raised with any number of methods: with a shaper, on a router table, or by hand. Without a doubt, the shaper is the most efficient tool you can use to raise panels. But shapers are expensive and routers lack the power to cut the profile in one pass. Because of these limitations, the table saw may be the best option for many woodworkers. Most woodworkers own table saws and the machine can easily make the cut in one pass.

    To set up your table saw for panel raising, it makes sense to build a jig. Of course, you can instead tilt the blade and guide the stock with the fence. But the fence on most saws lacks sufficient height to provide good support for the panel.

    A jig overcomes the support problem and offers other advantages as well. The broad surface area of the jig provides plenty of support, and the bevel angle is built in. So there's no need to tilt the blade and check the angle. Each time you use the jig, you'll save time. In addition, it's safer than using the fence.

    One final note: Construct the jig so that it fits in your saw's miter slot instead of just following the fence. This will prevent the jig (or work) from coming in contact with the back of the blade and causing kickback.

    Tombstone Doors

    Frame-and-panel doors can take on myriad designs. But certainly one of the most elegant examples is the tombstone door. A centuries-old design, the tombstone door is from a period when all woodworking was done by hand. Today, despite the beauty of the design, tombstone doors are not often seen.

    I'm sure that one reason is that the inside corners that flank the arch must be carved. That's because router bits and shaper cutters cut in an arc, and so they won't create inside corners. The solution is to carve the corners by hand. This process isn't really difficult just a bit time-consuming.

    If you would like to incorporate tombstone doors into your next project, there are several designs from which to choose.

    Door Joinery and Structural Strength

    Router bits and shaper cutters are available in several profiles, making it easy to achieve traditional door frame joinery. Cope-and-stick joinery is actually quite a simple concept. A profile is milled on the inside of the door stile (the vertical member), and its reverse profile or mirror image is milled on the rail (the horizontal member).

    In the process, a short tenon is formed that fits into the groove created for the panel. The last drawing shows a typical cope-and-stick router bit set. Single reversible bits are somewhat cheaper, but they can be fussier to set up.

    Cope-and-stick joinery is fast and efficient and is best used when you have a large number of doors to make, say, for a kitchen. But this method of construction is not as strong as a traditional mortise-and-tenon joinery. The short tongue or tenon created by the coping cut is typically only 3/8 inches (9.5 millimeters) and just doesn't have much long-grain gluing surface.

    So if you're building furniture for the ages, you'll want to consider the tried-and-true mitered sticking method, in which a regular tenon provides all the strength the frame will need to stand up to time.

    Lonnie Bird is a professional woodworker, teacher, writer, and tool designer whose work has been featured in several books on woodworking, Fine Woodworking magazine, and other publications.

    This article is excerpted from Shaping Wood, copyright 2001, available from The Taunton Press.



    ArchWeek Image

    Navigating multiple curves on a bandsaw.
    Photo: Lonnie Bird

    ArchWeek Image

    Mortise-and-tenon joinery gives strength to the work.
    Image: The Taunton Press

    ArchWeek Image

    A customized jig will make cuts safer and more convenient.
    Image: The Taunton Press

    ArchWeek Image

    The tombstone door, a traditional favorite.
    Image: The Taunton Press

    ArchWeek Image

    Tombstone doors are less common now because their inside corners must be hand carved.
    Image: The Taunton Press

    ArchWeek Image

    Cope-and-stick joinery is fast and efficient but not as strong as traditional mortise-and-tenon joinery.
    Image: The Taunton Press

    ArchWeek Image

    Router bits for cope-and-stick joinery.
    Image: The Taunton Press

    ArchWeek Image

    The Complete Illustrated Guide to Shaping Wood, published by Taunton Press.
    Image: The Taunton Press


    Click on thumbnail images
    to view full-size pictures.

    < Prev Page Next Page > Send this to a friend       Subscribe       Contribute       Advertise       Privacy       Comments
    AW   |   GREAT BUILDINGS   |   DISCUSSION   |   SCRAPBOOK   |   BOOKS   |   FREE 3D   |   SEARCH © 2002 Artifice, Inc. - All Rights Reserved